Difference between revisions of "Customizing a POP Kiosk"
(Created page with "== Overview == The POP Kiosk comes with default settings that make it suitable for use as an embedded kiosk, but many of these settings are fully customizable. You can easily...") |
|||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
{{DocumentationPage}} | |||
== Overview == | == Overview == | ||
The POP Kiosk comes with default settings that make it suitable for use as an embedded kiosk, but many of these settings are fully customizable. You can easily change the default resolution, display output, control wireless radios or change the boot logo. | The POP Kiosk comes with default settings that make it suitable for use as an embedded kiosk, but many of these settings are fully customizable. You can easily change the default resolution, display output, control wireless radios or change the boot logo. | ||
| Line 4: | Line 6: | ||
== Configuring the Raspberry Pi at Boot == | == Configuring the Raspberry Pi at Boot == | ||
The Raspberry Pi computer uses the <code>boot</code> partition to configure the computer system at each boot<ref>https://www.raspberrypi.com/documentation/computers/config_txt.html</ref> . You can edit these files by inserting the kiosk's SD card into a Windows or Mac computer and navigating to the <code>boot</code> drive that is automatically mounted. | The Raspberry Pi computer uses the <code>boot</code> partition to configure the computer system at each boot<ref>https://www.raspberrypi.com/documentation/computers/config_txt.html</ref> . You can edit these files by inserting the kiosk's SD card into a Windows or Mac computer and navigating to the <code>boot</code> drive that is automatically mounted. | ||
{{ExternalResource|[https://www.raspberrypi.com/documentation/computers/config_txt.html Raspberry Pi Documentation – The Config.txt File]}} | |||
=== Enabling 64-Bit Processing === | |||
Open the <code>/boot/config.txt</code> text file in a text editor and add the line <code>arm_64bit=1</code> to the end of the file. Save the file and insert the SD card back into the Raspberry Pi. | |||
{{Note|This will only work with the Raspberry Pi 4. This is not enabled by default to allow the POP image to work with the Raspberry Pi 3B+.}} | |||
=== Enabling Bluetooth === | === Enabling Bluetooth === | ||
Open the <code>/boot/config.txt</code> text file in a text editor and search for the line <code>dtoverlay=disable-bt</code>. Add a hash mark <code>#</code> to the beginning of the line so it reads <code>#dtoverlay=disable-bt</code>. Save the file and insert the SD card back into the Raspberry Pi. | Open the <code>/boot/config.txt</code> text file in a text editor and search for the line <code>dtoverlay=disable-bt</code>. Add a hash mark <code>#</code> to the beginning of the line so it reads <code>#dtoverlay=disable-bt</code>. Save the file and insert the SD card back into the Raspberry Pi. | ||
=== Changing Resolution === | |||
Open the <code>/boot/config.txt</code> text file in a text editor and search for the lines <code>framebuffer_width=800</code> and <code>framebuffer_height=480</code>. These values can be changed to better reflect the pixel dimensions of the display you are using. Save the file and insert the SD card back into the Raspberry Pi. | |||
=== Rotating the Touchscreen Display === | |||
Open the <code>/boot/config.txt</code> text file in a text editor and search for the lines <code>lcd_rotate=0</code> or <code>lcd_rotate=2</code> . A value of 0 uses the displays default orientation, while a value of 2 rotates the display by 180°. It is not easy to rotate the display and the touchscreen by 90° or 270°. Save the file and insert the SD card back into the Raspberry Pi. | |||
{{Note|This only applies to the Raspberry Pi official 7" touchscreen display.}} | |||
=== Enabling Wi-Fi === | === Enabling Wi-Fi === | ||
| Line 24: | Line 40: | ||
=== Changing the Boot Logo === | === Changing the Boot Logo === | ||
You can easily change the boot logo that is displayed while the kiosk is starting by replacing the <code>/boot/splash.png</code> image file. The file you replace it with must be a PNG file with the name <code>splash.png</code>. | You can easily change the boot logo that is displayed while the kiosk is starting by replacing the <code>/boot/splash.png</code> image file. The file you replace it with must be a PNG file with the name <code>splash.png</code>. | ||
=== Controlling the GPIO === | |||
The <code>/boot/config.txt</code> file can be used to control [https://www.raspberrypi.com/documentation/computers/config_txt.html#gpio the GPIO pins] and [https://www.raspberrypi.com/documentation/computers/configuration.html#part3.1 enable technologies needed for GPIO communication]. | |||
== Resources == | |||
<references />{{DocumentationNavigation}} | |||
Latest revision as of 17:19, 2 March 2023
Overview
The POP Kiosk comes with default settings that make it suitable for use as an embedded kiosk, but many of these settings are fully customizable. You can easily change the default resolution, display output, control wireless radios or change the boot logo.
Configuring the Raspberry Pi at Boot
The Raspberry Pi computer uses the boot partition to configure the computer system at each boot[1] . You can edit these files by inserting the kiosk's SD card into a Windows or Mac computer and navigating to the boot drive that is automatically mounted.
Enabling 64-Bit Processing
Open the /boot/config.txt text file in a text editor and add the line arm_64bit=1 to the end of the file. Save the file and insert the SD card back into the Raspberry Pi.
Enabling Bluetooth
Open the /boot/config.txt text file in a text editor and search for the line dtoverlay=disable-bt. Add a hash mark # to the beginning of the line so it reads #dtoverlay=disable-bt. Save the file and insert the SD card back into the Raspberry Pi.
Changing Resolution
Open the /boot/config.txt text file in a text editor and search for the lines framebuffer_width=800 and framebuffer_height=480. These values can be changed to better reflect the pixel dimensions of the display you are using. Save the file and insert the SD card back into the Raspberry Pi.
Rotating the Touchscreen Display
Open the /boot/config.txt text file in a text editor and search for the lines lcd_rotate=0 or lcd_rotate=2 . A value of 0 uses the displays default orientation, while a value of 2 rotates the display by 180°. It is not easy to rotate the display and the touchscreen by 90° or 270°. Save the file and insert the SD card back into the Raspberry Pi.
Enabling Wi-Fi
Open the /boot/config.txt text file in a text editor and search for the line dtoverlay=disable-wifi . Add a hash mark # to the beginning of the line so it reads #dtoverlay=disable-wifi. Save the file and insert the SD card back into the Raspberry Pi.
Connecting to a Wireless Network
Open the /boot/wpa_supplicant.conf file in a text editor. If it doesn't exist, create a new text file in the boot directory named wpa_supplicant.conf. It is common for Operating Systems to hide file extension, so you many need to verify this file is named wpa_supplicant.conf and not wpa_supplicant.conf.txt. This file needs to be formatted very specifically, according to Raspberry Pi specifications.
country=US # Your 2-digit country code
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
network={
ssid="YOUR_NETWORK_NAME"
psk="YOUR_PASSWORD"
key_mgmt=WPA-PSK
}Changing the Boot Logo
You can easily change the boot logo that is displayed while the kiosk is starting by replacing the /boot/splash.png image file. The file you replace it with must be a PNG file with the name splash.png.
Controlling the GPIO
The /boot/config.txt file can be used to control the GPIO pins and enable technologies needed for GPIO communication.
Resources
| Documentation | |
|---|---|
| Installation | Look and Feel |
| Interaction Modes | Developing Activity Types |
| Creating an Interactive | Framework |
| Integrating CLIO | Contribute |
