POP Kiosk Modular Case Adapter (part)

This section contains CLIO documentation.

This section requires photographs, illustrations or screenshots.

Overview

• 
• 
• 
• 
• 

This adapter is attached to the back, top or bottom of the kiosk using two M5 bolts. It can be used with any accessories created for the popular Modular Mounting System. It is printed in two parts and attached together with an M4 bolt and optional glue. The mount can be used with a two- or three-prong adapter.

Features

• Prints in two parts to improve long term durability
• Can be used to attach two-prong ("male") or three-prong ("female") Modular Mounting System accessories
• Adapter head can be attached to allow for either horizontal or vertical articulation
• Cut-outs allow for kiosk case heat ventilation

Specifications

Dimensions

The modular mount plate is 107.34mm x 25.74mm x 9.64mm. The two-prong modular mount head is 15.00mm x 15.00mm x 25.00mm. The three-prong modular mount head is 15.00mm x 17.00mm x 24.90mm.

Printed Parts

Part	Description	Quantity	Estimates		Example
			Print Time	Filament Usage
Modular Mount Plate	Flat plate that attaches to the kiosk case and can be used with a two- or three-prong mount head.	1	1 hour 30 minutes	10g
Modular Mount Head – Two-Prong	Head for the mount plate that can be used to attach two-prong ("male") accessories.	1	54 minutes	6g
Modular Mount Head – Three-Prong	Head for the mount plate that can be used to attach three-prong ("female") accessories.		1 hours 3 minutes	7g

Hardware

Part	Description	Quantity
M4-10mm machine screw	Attaches the mount head to the mount plate.	1

Material

This part is printed with polylactic acid (PLA) or other sturdy plastic, such as Polypropylene (PP) or Acrylonitrile styrene acrylate (ASA).

Printing This Part

Slicing

Orientation

Part	Notes	Example
Modular Mount Plate	We recommend printing this part with the flat side directly on the build plate.
Modular Mount Head – Two-Prong	We recommend printing this part with the prongs parallel to the build plate.
Modular Mount Head – Three-Prong	We recommend printing this part with the prongs parallel to the build plate and the rounded edge pointed up.

Settings

Modular Mount Plate

We start with the default "Standard Quality" 0.2 mm print profile. We recommend the following settings overrides:

Setting	Recommendation	Notes
Shell - Wall Line Count	4	This was increased from the default to increase the durability when higher amounts of stress are applied.
Shell - Bottom Layers	4	This will provide sturdy walls for each prong.
Shell - Top Layers	4	This will provide sturdy walls for each prong.
Infill - Density	45	This part can be subject to high stress and more infill will provide greater structural integrity.
Infill - Pattern	Tri-Hexagon Cubic Subdivision	These infill patterns provide good internal support in multiple directions.  Tri-Hexagon uses less filament but is also less durable.
Speed - Print Speed	40mm/s	For final production prints, we recommend printing slower than average to decrease stringing with small holes.
Support - Generate Support	Yes	This part has a small overhang that would be improved by supports.
Support - Support Structure	Tree	We highly recommend tree supports instead of normal supports. They take more time, but they require less filament and are much easier to remove.
Support - Support Placement	Touching Buildplate	Only printing supports that touch the build plate are much easier to remove from this print.
Build Plate Adhesion - Adhesion Type	None	This part has a lot of contact with the print bed and should not require a raft.

Modular Mount Head – Two-Prong

We start with the default "Standard Quality" 0.2 mm print profile. We recommend the following settings overrides:

Setting	Recommendation	Notes
Shell - Wall Line Count	4	This was increased from the default to increase the durability when higher amounts of stress are applied.
Shell - Bottom Layers	4	This will provide sturdy walls for each prong.
Shell - Top Layers	4	This will provide sturdy walls for each prong.
Infill - Density	45	This part can be subject to high stress and more infill will provide greater structural integrity.
Infill - Pattern	Tri-Hexagon Cubic Subdivision	These infill patterns provide good internal support in multiple directions.  Tri-Hexagon uses less filament but is also less durable.
Speed - Print Speed	40mm/s	For final production prints, we recommend printing slower than average to decrease stringing with small holes.
Support - Generate Support	Yes	This part has a lot of overhangs that require the use of supports.
Support - Support Structure	Tree	We highly recommend tree supports instead of normal supports. They take more time, but they require less filament and are much easier to remove.
Support - Support Placement	Touching Buildplate	Only printing supports that touch the build plate are much easier to remove from this print.
Build Plate Adhesion - Adhesion Type	Raft	This part is small and uses a lot of supports, so it is recommended to use a raft.

Modular Mount Head – Three-Prong

We start with the default "Standard Quality" 0.2 mm print profile. We recommend the following settings overrides:

Setting	Recommendation	Notes
Shell - Wall Line Count	4	This was increased from the default to increase the durability when higher amounts of stress are applied.
Shell - Bottom Layers	4	This will provide sturdy walls for each prong.
Shell - Top Layers	4	This will provide sturdy walls for each prong.
Infill - Density	45	This part can be subject to high stress and more infill will provide greater structural integrity.
Infill - Pattern	Tri-Hexagon Cubic Subdivision	These infill patterns provide good internal support in multiple directions.  Tri-Hexagon uses less filament but is also less durable.
Speed - Print Speed	40mm/s	For final production prints, we recommend printing slower than average to decrease stringing with small holes.
Support - Generate Support	Yes	This part has a lot of overhangs that require the use of supports.
Support - Support Structure	Tree	We highly recommend tree supports instead of normal supports. They take more time, but they require less filament and are much easier to remove.
Support - Support Placement	Touching Buildplate	Only printing supports that touch the build plate are much easier to remove from this print.
Build Plate Adhesion - Adhesion Type	Raft	This part is small and uses a lot of supports, so it is recommended to use a raft.

Results

Printers

This part has been print tested with the following 3D printers:

Manufacturer	Model	Notes
Creality	CR-10 Mini	Excellent print quality. Reliable machine.
Creality	CR-10	Excellent print quality. Reliable machine.
Creality	Ender 3 SR-1 Pro

Build Surface

This part has been print tested with the following build surfaces:

Method	Notes
Painter's tape
Glue stick	Creates an uneven and non-uniform first print layer appearance.
Adhesive build surface	First layer may have problems printing full height depending on type and hardness of build surface, but this does not affect the overall printability.
Polyetherimide (PEI) build plate	Small parts will require a raft.

Filament

This part has been print tested with the following materials:

Filament	Manufacturer	Notes
Overture PLA	Overture	Excellent build quality and durability. Good for prototyping or production kiosks.
Amazon Basics PLA	Amazon	Decent build quality and durability. Recommended for rapid prototyping.

References

Documentation
Installation	Look and Feel
Interaction Modes	Developing Activity Types
Creating an Interactive	Framework
Integrating CLIO	Contribute