POP Kiosk Foot (part)

This section requires photographs, illustrations or screenshots.

Overview

The foot is used to display the kiosk on a flat surface, such as a table or shelf.  It is printed in two parts then attached together with an M4 bolt and optional glue.  The foot can be used with a two- or three-prong adapter.  The foot can be used with suction cups to more securely attach to sheer surfaces, such as glass or polished stone.  Additionally, 3D printed TPU or third-party anti-slip grips can be attached to the bottom.

Features

• Prints in two parts to improve long term durability
• Can be used to attach two-prong ("male") or three-prong ("female") Modular Mounting System accessories.
• Can be used with M5 screw-on suction cups or 3D printed TPU anti-slip grips

Specifications

Dimensions

The kiosk foot measures 189.22mm x 164.92mm x 21.74mm.

Printed Parts

Part	Description	Quantity	Estimates		Example
			Print Time	Filament Usage
Kiosk Foot	Provides a stable base on flat surfaces	1	7 hours 26 minutes	63g
Modular Mount Head – Two-Prong	Head for the mount plate that can be used to attach two-prong ("male") accessories.	1	54 minutes	6g
Modular Mount Head – Three-Prong	Head for the mount plate that can be used to attach three-prong ("female") accessories.		1 hours 3 minutes	7g

Hardware

Part	Description	Quantity
M4-10mm machine screw	Attaches the kiosk foot to the modular mount head	1
M5-5mm suction cups	Suction cups can provide additional stability on sheer surfaces.	3

Material

This part is printed with polylactic acid (PLA) or other sturdy plastic, such as Polypropylene (PP) or Acrylonitrile styrene acrylate (ASA).

Printing This Part

Slicing

Orientation

Part	Notes	Example
Kiosk Foot	We recommend printing this part with the bottom of the foot touching the build plate.
Modular Mount Head – Two-Prong	We recommend printing this part with the prongs parallel to the build plate.
Modular Mount Head – Three-Prong	We recommend printing this part with the prongs parallel to the build plate and the rounded edge pointed up.

Settings

Kiosk Foot

We start with the default "Standard Quality" 0.2 mm print profile. We recommend the following settings overrides:

Setting	Recommendation	Notes
Shell - Wall Line Count	4	This was increased from the default to increase the durability when higher amounts of stress are applied.
Shell - Bottom Layers	4	This will provide sturdy walls for each prong.
Shell - Top Layers	4	This will provide sturdy walls for each prong.
Infill - Density	45	This part supports the kiosk and the extra infill weight helps with providing a sturdy base.
Infill - Pattern	Tri-Hexagon Cubic Subdivision	These infill patterns provide good internal support in multiple directions.  Tri-Hexagon uses less filament but is also less durable.
Speed - Print Speed	40mm/s	For final production prints, we recommend printing slower than average to decrease stringing with small holes.
Support - Generate Support	No	This part has no overhangs.
Build Plate Adhesion - Adhesion Type	None	This part has a lot of contact with the print bed and should not require a raft.

Modular Mount Head – Two-Prong

We start with the default "Standard Quality" 0.2 mm print profile. We recommend the following settings overrides:

Setting	Recommendation	Notes
Shell - Wall Line Count	4	This was increased from the default to increase the durability when higher amounts of stress are applied.
Shell - Bottom Layers	4	This will provide sturdy walls for each prong.
Shell - Top Layers	4	This will provide sturdy walls for each prong.
Infill - Density	45	This part can be subject to high stress and more infill will provide greater structural integrity.
Infill - Pattern	Tri-Hexagon Cubic Subdivision	These infill patterns provide good internal support in multiple directions.  Tri-Hexagon uses less filament but is also less durable.
Speed - Print Speed	40mm/s	For final production prints, we recommend printing slower than average to decrease stringing with small holes.
Support - Generate Support	Yes	This part has a lot of overhangs that require the use of supports.
Support - Support Structure	Tree	We highly recommend tree supports instead of normal supports. They take more time, but they require less filament and are much easier to remove.
Support - Support Placement	Touching Buildplate	Only printing supports that touch the build plate are much easier to remove from this print.
Build Plate Adhesion - Adhesion Type	Raft	This part is small and uses a lot of supports, so it is recommended to use a raft.

Modular Mount Head – Three-Prong

We start with the default "Standard Quality" 0.2 mm print profile. We recommend the following settings overrides:

Setting	Recommendation	Notes
Shell - Wall Line Count	4	This was increased from the default to increase the durability when higher amounts of stress are applied.
Shell - Bottom Layers	4	This will provide sturdy walls for each prong.
Shell - Top Layers	4	This will provide sturdy walls for each prong.
Infill - Density	45	This part can be subject to high stress and more infill will provide greater structural integrity.
Infill - Pattern	Tri-Hexagon Cubic Subdivision	These infill patterns provide good internal support in multiple directions.  Tri-Hexagon uses less filament but is also less durable.
Speed - Print Speed	40mm/s	For final production prints, we recommend printing slower than average to decrease stringing with small holes.
Support - Generate Support	Yes	This part has a lot of overhangs that require the use of supports.
Support - Support Structure	Tree	We highly recommend tree supports instead of normal supports. They take more time, but they require less filament and are much easier to remove.
Support - Support Placement	Touching Buildplate	Only printing supports that touch the build plate are much easier to remove from this print.
Build Plate Adhesion - Adhesion Type	Raft	This part is small and uses a lot of supports, so it is recommended to use a raft.

Results

Printers

This part has been print tested with the following 3D printers:

Manufacturer	Model	Notes
Creality	CR-10 Mini	Excellent print quality. Reliable machine.
Creality	CR-10	Excellent print quality. Reliable machine.
Creality	Ender 3 S-1 Pro

Build Surface

This part has been print tested with the following build surfaces:

Method	Notes
Painter's tape
Glue stick	Creates an uneven and non-uniform first print layer appearance.
Adhesive build surface	First layer may have problems printing full height depending on type and hardness of build surface, but this does not affect the overall printability.
Polyetherimide (PEI) build plate	Some parts may require a raft if there are issues with the first layer adhering.

Filament

This part has been print tested with the following materials:

Filament	Manufacturer	Notes
Overture PLA	Overture	Excellent build quality and durability. Good for prototyping or production kiosks.
Amazon Basics PLA	Amazon	Decent build quality and durability. Recommended for rapid prototyping.