|
|
| Line 15: |
Line 15: |
|
| |
|
| == Printing the Case == | | == Printing the Case == |
| | {{Main|Printing the POP Kiosk Case}} |
| The POP kiosk is made from a collection of modular parts that can be printed separately and assembled into different configurations based on your specific needs and application. | | The POP kiosk is made from a collection of modular parts that can be printed separately and assembled into different configurations based on your specific needs and application. |
| === Case ===
| |
| {{Main|POP Kiosk Case (part)}}
| |
|
| |
|
| This is the main case that protects the Raspberry Pi computer and touchscreen display.
| |
| === Protection ===
| |
| ==== Collar ====
| |
| {{Main|POP Kiosk Collar (part)}}
| |
|
| |
| The collar protects the exposed edges of the Raspberry Pi touchscreen display, decreasing the chances that the kiosk screen will be damaged from minor bumps and falls. It is printed in two parts and held together by M2 screws.
| |
|
| |
| ==== Bumper ====
| |
| {{Main|POP Kiosk Bumper (part)}}
| |
| The bumper also protects the exposed edges of display, but it is printed as one part with a soft and flexible TPU filament. When printed with specific infill settings, it can provide additional protection to bumps and falls. This bumper is used instead of the collar and was created for use in mobile pop-up exhibits.
| |
|
| |
| ==== Cover ====
| |
| {{Main|POP Kiosk Cover (part)}}
| |
| The cover provides protection to the front of the kiosk display by attaching directly to the collar or bumper. This cover was created to provide protection to the glass screen during transport and storage.
| |
|
| |
| === Mount ===
| |
|
| |
| ==== Modular Case Adapter ====
| |
| {{Main|POP Kiosk Modular Case Adapter (part)}}
| |
| This adapter is attached to the back, top or bottom of the kiosk using two M5 bolts. It can be used with any accessories created for the popular Modular Mounting System<ref name=":0">https://www.thingiverse.com/thing:2194278</ref>. It is printed in two parts and attached together with an M5 bolt and optional glue. The mount can be used with a two- or three-prong adapter.
| |
|
| |
| ==== Arm ====
| |
| {{Main|POP Kiosk Arm (part)}}
| |
| There are 30mm, 60mm, 90mm 150mm and 240mm arm attachments for the Modular Mounting System. These can be used to extend the length of the mount system, but caution should be used to verify that the kiosk is fully supported. This includes axis changers and prong adapters.
| |
|
| |
| ==== Foot ====
| |
| {{Main|POP Kiosk Foot (part)}}
| |
| The foot is used to display the kiosk on a flat surface, such as a table or shelf. It is printed in two parts then attached together with an M5 bolt and optional glue. The foot can be used with a two- or three-prong adapter. The foot can be used with suction cups to more securely attach to sheer surfaces, such as glass or polished stone. Additionally, 3D printed TPU or third-party anti-slip grips can be attached to the bottom.
| |
|
| |
| ==== Thumbscrews ====
| |
| {{Main|POP Kiosk Thumbscrew (part)}}
| |
| The thumbscrews are used with standard M5 bolts to make it easier to tighten and loosen the display for repositioning.
| |
|
| |
|
| == Assembling the Kiosk == | | == Assembling the Kiosk == |
Introduction
The CLIO kiosk prototype is designed to have a mobile and modular form factor. All hardware is easily replaceable in the event of hardware damage or failure. It is constructed using off-the-shelf parts and does not require any soldering. Raspberry Pi hardware facilitates easy cloning of the kiosk system, allowing the institution to create additional kiosks in-house as demand dictates.
For the pilot test, all required parts were fabricated using a Creality CR-10 Mini 3D printer. This includes a case, mount, stand, collar and screen protector. To improve longevity, we purchased standard metric metal hardware instead of printing it.
Overall, the total cost per kiosk, including electronics, hardware, and filament is $220. The kiosk leverages designs that are available through online repositories under permissive licenses, as well as custom parts created specifically for this project.
Preparing the Hardware
Test
Preparing the Software
Test
Printing the Case
The POP kiosk is made from a collection of modular parts that can be printed separately and assembled into different configurations based on your specific needs and application.
Assembling the Kiosk
Finishing the Case
Test
Securing the Nuts
Test
Installing Dust Screens
Test
Installing the 30mm Fan
Test
Installing the Panel Mount
Test
Updating the Kiosk
Test
References
